Sale!

Roadvision DIMMER CONTROL SWITCH RDIMG2

$77.00 $69.00

The LED Dimmer Control Switch is designed for use on all Roadvision Next Generation Light Bars – allowing you to change the brightness of the lights to suit changing conditions (from 50% to 100% output), without affecting the light colour. Turn your lights down if there’s a bit of traffic around, and turn them up for maximum brightness.

Comes with a 7 YEAR WARRANTY!!!

Compatible with the following 3 Roadvision Bar Light Series:

SR2  |  DC2  |  DCX2

Description

The LED Dimmer Control Switch is designed for use on all Roadvision Next Generation Light Bars – allowing you to change the brightness of the lights to suit changing conditions (from 50% to 100% output), without affecting the light colour. Turn your lights down if there’s a bit of traffic around, and turn them up for maximum brightness.

The Dimmer Control Switch is easy to install with plug and play technology and is suitable for positive or negative switched head lamp systems.

Compatible with the following 3 Roadvision Bar Light Series:   SR2  |  DC2  |  DCX2

Comes with a 7 YEAR WARRANTY!!!

 

FITTING INSTRUCTIONS

  1. Find a suitable flat location on the dash to mount the Dimmer Controller.
  2. If required pre-drill a hole for the cable to pass through the dash or alternatively pass the cable through an existing opening.
  3. Using either the 3M double sided tape, or M4 screws, fix the controller bracket to the dash.
  4. Pass the two wires through a grommet in the vehicle firewall making sure the cables will not rub on any sharp edges.
  5. Connect the 4 pin LEDLinkTM twist lock plug to the matching socket from your Roadvision Next Generation LED Light Bar.
  6. For vehicles fitted with HB3 or H4 bulbs, plug the relevant piggy back connector into the high beam lead from the dimmer controller. (part numbers; HB3 – RPBCHB3 or H4 – RPBCH4 both sold separately).
  7. Unplug the vehicles head lamp plug (high beam) from the back of one of the head lamp bulbs and plug the piggy back connector into both the globe and vehicle harness.
  8. For vehicles where a piggy back connector cannot be installed, identify the positive high beam feed and connect the red wire, connect the black wire to the negative feed to the high beam. Ensure to solder or use an appropriate crimp terminal and insulate the bare wires with heat shrink or electrical tape.
  9. Connect the Roadvision Next Generation light bars 2 pin Deutsch or ATP plug directly to the battery with an appropriate fuse installed on the positive feed. (part numbers; Deutsch – RPCDT3M or ATP – RPCATP3M both sold separately).
  10. Secure all access wire to the vehicle.

 

EASY TO FIT…

OPERATION

  1. Turn On the vehicle ignition and high beams ON.
  2. ON/OFF switch (1) will illuminate Blue on Dimmer Controller, unit is in standby mode.
  3. Push the ON/OFF (1) switch to turn light bar ON, ON/OFF switch & dimmer knob (2) will illuminate white when ON.
  4. With light bar ON, rotate dimmer knob (2) clockwise to increase brightness, counter clockwise to decrease brightness.

 

EASY TO USE…

Roadvision DIMMER CONTROL SWITCH RDIMG2 was last modified: by

Pickup

If you choose pick up when ordering your items through our shop, please wait for us to call you when your items are ready for pick up. This generally takes 1-3 days.

You can then pick up your order from our SHOWROOM:

1/29 May Holman Drive, Bassendean WA-6054

Please note that we do not regularly stock all items in our showroom so please wait for us to confirm it’s ready for pickup or call us to check availability!

Our opening hours are:

Monday: 09:00 am – 4:00 pm
Tuesday – Friday: 09:00 am – 2:00 pm

or by appointment

Find more information about our showroom here.

 

DELIVERY

We exclusively deliver to Perth & Surroundings – please scroll down to see a the delivery areas.

TIMES & FEES

  • STANDARD $15 – Generally takes 1-3 business days, in rare cases it may take longer.
  • EXPRESS $30 – Next day delivery if ordered before 12pm on a business day.

NOTE: Products from the following brands may take longer due to manufacturers’ stock levels. If this is the case we will contact you.

Some products are not available for express delivery due to the same reason. If this is the case you can see a note at the bottom the products description.
Dolphin, Dometic, Intervolt, Latronics, Noco, Projecta, Wema

See ‘Express delivery exempt products’ below for more information.

We try to be as accurate as possible with our stock information and delivery times. However sometimes delays occur due to manufacturer’s stock levels. If we are not able to deliver a product on time, we will contact you immediately. Please make sure you provide us with your CORRECT CONTACT DETAILS (phone & email) to unsure we can reach you.

 

DELIVERY AREAS

If you are at the border of the delivery area and not sure if we deliver to your address, please don’t hesitate to contact us and we will check for you.


 

AVAILABILITY

Express delivery exempt products

Products from certain brands might have longer delivery times due to the manufacturer’s stock levels and are not available for express delivery. This delivery restriction is applied on products including but not limited to the following brands: DOLPHIN, DOMETIC, INTERVOLT, LATRONICS, WAECO, WEMA

Reasons for order delays

  • Entry of an incorrect or incomplete address during checkout.
  • The address had no-one to sign for the parcel, and “Authority to Leave” was not selected at checkout.
  • Incorrect payment information was entered against the order. Please double check all details at time of checkout as your order will only be created upon receipt of payment.
  • In the event an order is flagged for verification we may need to get in contact via phone before dispatching some orders. Personal details may need to be confirmed for fraud prevention if we are unable to verify the shipping destination to protect the card holder, and this may delay shipping.
  • Occasionally if a particular item is in high demand, we may need to supply the product from outside of our standard delivery network. This can cause delays in dispatch. If your order is not received within the quoted delivery period please contact us. We will generally respond to online enquiries within 24 hours.

 

DELIVERY INSTRUCTIONS

All deliveries are done by ourselves or by a courier service so products cannot be delivered to PO Boxes. At the checkout you will have to choose between SIGNATURE REQUIRED and AUTHORITY TO LEAVE.

We recommend all deliveries be shipped to a location that is attended during business hours, whether that is a home or work address, to minimise any inconvenience and redelivery fees.

Authority to leave

This gives the delivery person the permission to leave your order in front of the house if no one opens the door at delivery.

PLEASE NOTE: If the address is unattended Perth Pro Auto Electric Parts can’t be held liable if the order is stolen. Only choose this option if you think the address is a safe place to have an item sitting in front of your door. Do NOT choose this option if you live in an apartment building or block of flats as the delivery person may not have access to the building and won’t be able to leave it in front of your door.

Signature required

This means the delivery person can only leave your order if someone answers the door and signs for the receipt of the order.

PLEASE NOTE: Only choose this option if the address is attended during business hours as if no one is present to sign for the receipt, your order has to be taken back and you may have to pay a redelivery fee.


 

RETURNS

Please see our Returns Policy for further information.


Roadvision DIMMER CONTROL SWITCH RDIMG2 was last modified: by